Leading G.fast DPU Reference Design - Sckipio DP3016-EVM
16116
page,page-id-16116,page-template,page-template-full_width,page-template-full_width-php,ajax_fade,page_not_loaded,,qode-title-hidden,qode-theme-ver-9.2,wpb-js-composer js-comp-ver-4.11.2.1,vc_responsive

DP3016-EVM G.FAST DPU REFERENCE DESIGN

Everything You Need to Design your DPU

OVERVIEW

The Sckipio DP3016-EVM G.fast DPU Reference Design is a complete G.fast DPU solution including all the hardware and software needed to evaluate G.fast in a Fiber-to-the-Distribution-Point (FTTdp) installation.

 

The DP3016-EVM implements 16 FTU-O transceivers that comply with the ITU G.fast recommendations (G.9700/1) as well as additional functionalities required within the Distribution Point Unit (DPU) and defined within the G.9701 System Reference Model Recommendation.

DP3016 G.fast DPU Reference Design

DP3016 G.fast DPU Reference Design

The Sckipio DP3016-EVM is designed for ultra high speed broadband for MDU, Single Family Units and businesses. It also is an excellent solution for cellular backhaul.

REFERENCE MATERIALS

Broad Standards Support
  • Fully compliant with the ITU-T G.fast Recommendation (G.9700/1)
  • Supports the complete 106a profile
  • Compliant with ITU-T G.999.1 interface recommendation
  • Supports ITU-T G.997.1 and future extensions for G.fast
  • Support for TR-156 and TR-167 Broadband Forum Architectures
  • Support for IEEE 1588 Time Synchronization
  • Supports ITU G.994.1 G.hs
  • Spectrally co-existent with legacy technologies, e.g. ADSL, VDSL
Full G.fast Performance
  • Bandwidth: 2 – 106MHz (programmable)
  • Max PHY rate: 1Gbps per line
  • Flexible downlink/uplink bit rate ratio
Vectoring Control Engine
  • On-chip VCE providing system-level vectoring
  • Vectoring group size of up to 64 lines
  • Scalable VCE processing power
Low Power Consumption
  • Locally power 110/220 VAC (50-60 Hz).
  • Average end-to-end transceiver power of 1.5 watts per line
  • Low power modes supported across the whole reference design (DFE and AFE)
  • Multiple power save modes lowering actual consumption under real life conditions
  • Full discontinuous mode support for lower actual consumption under real-life conditions
  • Support for L2.0, L2.1 low power states
L2+ Networking
  • 1:16 Ethernet to G.fast port switching
  • Classification based on VLAN, Ethernet MAC Address (DA/SA) or G.999.1 Stream ID
  • Up to 8 QoS priority queues per G.fast port
  • QoS-aware congestion control “Learning Bridge” mode for DA to G.fast port mapping
  • Multicast packet replication based on multicast groups
Time and Synchronization
  • Time-of-Day (ToD) synchronization to external clock reference
  • Synchronization using low accuracy management protocol, IEEE 1588 or one PPS signal
  • 8KHz Network Time Reference (NTR) support between DP and CPE
Interfaces
  • Two SFP optical interfaces with G.999.1 support
  • Support up to 2.5G downstream/1.25G upstream via GPON
  • One Gigabit Ethernet port
  • One 100Mbps Ethernet port for management
  • One USB port 2.0 for management and diagnostics
  • 16 twisted pair patch panel
Management and Configuration
  • Configuration interface for customized functionality
  • Remotely upgradeable firmware
  • Full statistics and performance monitoring
Miscellaneous
  • Full development system and reference design for fast time-to-market
  • 25 centimeters wide, 18 centimeters deep, 4.6 centimeters high